A truck leaves with four drops. The first customer's pallets are at the very front, behind everyone else's. At drop one the driver and the receiving crew unload nine pallets that do not belong there, take out the three that do, then lift the nine back on and re-strap them. The window at drop one is missed, and the other three windows slip behind it.
Nobody planned that. The loader simply loaded in the order the pallets came out of the warehouse. This article is for the logistics or warehouse manager who sends multi-drop trucks out. It is a method, not a Thai study. The figures below are illustrations, and they are labelled as such.
Short answer
- Load in reverse order of the drops. The last drop goes on first, deepest. The first drop goes on last, nearest the door.
- Fix the route before loading starts, and print a loading list in loading order. The loader should not have to work out the sequence.
- Mark every pallet with its drop number. The driver can then check the load in seconds.
- Weight and sequence can clash. Weight wins. A load that is over an axle limit or unstable is worse than a slow unload. Plan both together.
- Treat a route change after loading as a re-load. Price it, or do not allow it.
Why order is a cost, not a habit
Every pallet that has to be moved to reach another pallet is work that earns nothing. It is paid for in three places:
- Time at the stop. This is the time your receiver sees, and it is what eats the delivery window. For how a window is a block of the vehicle's day, see delivery time windows.
- Damage. Every extra lift is a chance to catch a corner or a wrapped pallet.
- Security of the load. Every re-stack is a point where straps are loosened and may not be pulled as tight again. See securing the load.
An illustration
This is not Thai data. The numbers are chosen to show the arithmetic.
- One truck, four drops, three pallets per drop, so twelve pallets.
- The only door is at the back. The pallets sit in four layers, each layer three pallets, layer one nearest the door.
- Assume 1.5 minutes for each extra pallet movement, including the repositioning of the forklift or hand trolley.
Right order. Drop one is in layer one, drop two in layer two, and so on. At each stop the three pallets come straight out. Extra movements: none.
Wrong order. Drop one is in layer four, the deepest. At drop one, layers one to three come out first (nine pallets) and go back afterwards (nine more). At drop two, layers one and two come out (six) and go back (six). At drop three, one layer comes out (three) and goes back (three). Drop four is nearest the door.
- Extra movements: 2 Γ (9 + 6 + 3) = 36.
- Extra time: 36 Γ 1.5 = 54 minutes.
That is 54 minutes of a driver's day and of three receiving docks, in return for nothing. The first drop pays the most, and it is the drop where a missed window is most likely to knock the rest of the route off. If you use a standard time for each stop, the standard time for a delivery round shows where to put it. A standard time that assumes the right order is wrong the day the load is in the wrong order.
How to do it
1. Freeze the route first
The loading order can only be right if the route is final. Set a cut-off time after which the route does not change, and tell the person who plans and the person who loads what it is. A route changed after the truck is loaded is a re-load, whatever it is called.
2. Print the loading list in loading order
The route sheet shows drops in driving order: first drop at the top. The loading list shows the same drops in reverse: last drop at the top. Two lists from the same plan, one for the driver and one for the loader. The loader works down the list and never has to think about the sequence.
3. Mark the pallets
Write the drop number large on each pallet or on the wrap, on the side that faces the door or the gap. The loader can check the stacking by eye. The driver can check the load before leaving. The receiver's crew can pick out what is theirs.
4. Check the weight at the same time
The reverse order is a starting point, not a command. Three other things can override it:
- Heavy goods low and near the centre of the truck. If the last drop is the lightest, you may still need the heavy pallets from drop one near the middle of the bed rather than at the door.
- The legal load on each axle. Where the load sits changes how it is shared between the axles. Check the split before the truck leaves. Axle load planning shows how.
- Fragile or wet-sensitive goods. These go where nothing is stacked on them and where the weather cannot reach, whatever their drop number.
When two of these clash, plan the load as one problem, not two. If you cannot get both, put the weight right and accept some extra movement at one stop. Add that stop's extra minutes to the route.
Where the body type changes it
The rule above assumes a single door at the back. A truck that opens along its side, such as one with curtains or a side door, lets the crew reach any position without lifting the pallets in front. Then the cost is not the lifting but the open side: the whole load is exposed and the straps across it are released at once. On that body the better sequence is still the reverse one, but for a different reason: it keeps the straps of the later drops untouched. For rain exposure on each body type, see the article on truck body type and rain.
A sealed door
If the rear door carries a seal, the first drop breaks it. Decide before the truck leaves who breaks it, who records the number, and whether the driver fits a new seal for the remaining drops and notes its number on the paperwork. If nobody decides, the receiver at drop four finds a broken seal and cannot tell why. This matters most when the goods are valuable.
What to do this week
- Pick the route that has the most drops. Look at its last three loads: in what order were the pallets loaded, and in what order were they unloaded?
- If the two orders were the same, count the extra movements as in the illustration and put a time on them.
- Add a second list for the loader, in reverse order of the route.
- Ask the driver to check the drop numbers on the pallets before leaving.
- Set the cut-off for route changes, and say what happens after it.
Where the evidence stops
- No Thai study of loading order, or of unloading time against loading order, was found. The method is standard practice for multi-drop work, and the reasoning is arithmetic, not measurement.
- The 1.5 minutes per movement is an assumption for the illustration. Time your own dock for a week and use your own number.
- The notes on side-opening bodies and on seals come from how the vehicles work, not from a Thai source. Check them against your own trucks.
