VWTVWT
← All insights

Loading a Truck So Every Axle Is Legal in Thailand

Published November 7, 2026 Β· 7 min read

A truck leaves the dock at 14.0 tonnes in total. Its limit is 15.0. The load planner signs it off. At the first weighbridge the rear axle reads 12.0 tonnes against a limit of 11.0, and the truck is overloaded while the total is fine.

Thai weight limits are not one number. They are at least two on every truck, and a third on every road. This article is about the second one, the axle, and how to plan a load so it stays inside.

Three limits on every trip

  1. The total. The weight of the truck plus its load. This is the number most people know.
  2. The axle, or the axle group. The most that may rest on the rear axle, or on a pair of axles working together.
  3. The road. Highway directors can set their own weight limits for a road, and a posted sign overrides the general table. Which office sets which road is in master data before software.

A load has to pass all three. The total is easy to check, because it is the sum of the pallets. The axle is not, because it depends on where on the floor each pallet sits.

What the Thai table says

Two Royal Gazette announcements by municipal highway directors were read in Thai, one from Pathum Thani and one from Maha Sarakham. Both are made under Section 61 of the Highway Act, and both carry the same table. The limits depend on the number of axles and on whether the tyres are single or in pairs, not on the word "6-wheel" or "10-wheel".

Truck Axle or axle group limit Total limit
Two axles, four wheels, single tyres at the rear 7.0 t on the rear axle 9.5 t
Two axles, six tyres (paired at the rear) 11.0 t on the rear axle 15.0 t
Three axles, ten tyres (rear pair of axles with paired tyres) 20.0 t on the rear pair 25.0 t
Four axles, twelve tyres (two steering axles, rear pair with paired tyres) 20.0 t on the rear pair 30.0 t

A tractor with a semi-trailer has limits on the trailer's axles as well: 7 or 11 tonnes for one axle depending on tyres, 13 or 20 tonnes for a pair, and 25.5 tonnes for a group of three. Its total runs from 45 up to 50.5 tonnes, and it depends on the distance from the kingpin to the trailer axles: 45 tonnes from 4.5 m, 47 from 6 m, 49 from 7 m and 50.5 from 8 m (for a three-axle tractor with a three-axle trailer).

Where the evidence stops: these are announcements for local highways in two municipalities. National highways and motorways are governed by a separate announcement from the Department of Highways, which was not read directly here. The totals this site already uses for national roads, 25 tonnes for a ten-wheel rigid and 50.5 tonnes for the long semi-trailer combination, match this table, which suggests a shared pattern. Treat it as the pattern, and check the actual announcement for the road you use. A posted sign on a bridge or road overrides it.

The same announcements also ban a vehicle whose axles, wheels or tyres differ from the table unless the highway director gives permission. A truck that does not appear on the table is not safe by default.

Why the axle fails first on a small truck

An axle carries the share of the load that sits nearest to it. The rule is the lever you know from a seesaw. A load placed over the rear axle puts all its weight on that axle. A load placed halfway between the front and rear axles puts half on each. A load placed behind the rear axle puts more than all of its weight on the rear axle and takes weight off the front.

The worked case below is an illustration. Use your own truck's weights.

A six-tyre two-axle truck weighs 5.5 tonnes empty: 2.5 on the front axle, 3.0 on the rear. The distance between the axles is 4.0 m. The table allows 11.0 tonnes on the rear and 15.0 in total. The total limit leaves room for 9.5 tonnes of load. The rear axle has 8.0 tonnes of room (11.0 minus its own 3.0).

Where the load's centre sits, measured from the front axle Share on the rear axle Most load the rear axle allows Which limit binds
2.0 m (halfway between the axles) 50% 16.0 t The total, at 9.5 t
3.2 m 80% 10.0 t The total, at 9.5 t
3.8 m 95% 8.4 t The rear axle
4.4 m (0.4 m behind the rear axle) 110% 7.3 t The rear axle

With 9.5 tonnes of load whose centre sits 3.8 m back, the rear axle carries 3.0 + 9.5 Γ— 0.95 = 12.0 tonnes, which is 1.0 tonne over. With the centre at 4.4 m it carries 13.5 tonnes, which is 2.5 tonnes over, and the front axle is down to about 1.6 tonnes, so the steering gets light. The total on the scale is 15.0 tonnes both times. The plan passes the total and fails the axle.

The fix needs no new truck. It is where the pallets go. Heavy pallets belong between the axles, light ones towards the ends. The same 9.5 tonnes with its centre at 3.2 m puts 10.6 tonnes on the rear axle, which is legal.

The same arithmetic shows why the larger trucks tolerate more. A ten-tyre three-axle rigid has a rear pair allowed 20 tonnes. If the truck weighs 9 tonnes empty, with 5 of them on that pair, the pair has 15 tonnes of room, and the total limit allows at most 16 tonnes of load. Only a load almost entirely over the rear pair hits the axle limit before the total.

What happens to the axles after each drop

On a multi-drop route the load changes at every stop. The textbook warns that taking off part of a load can change the spread of weight over the axles and leave one axle illegally heavy.

Do the arithmetic and one thing is clear. Taking away a pallet that sits between the axles makes both axles lighter, never heavier. Each axle carries a positive share of it, so removing it lowers both. The illegal axle after a drop therefore comes from one of two things:

  • A load sitting behind the rear axle. Take it off and the front axle gets heavier, not lighter. Rare on a flat bed, common on a body with a long tail.
  • The driver or the dock crew moving what is left. After three drops the remaining pallets are pushed to the back "to make room", or slid forward to get at a door. The rear axle load then changes because the loads moved, not because any were removed.

The first load check is at the dock. The second is the plan for the remainder at each stop. A route plan that lists drops in order can state, for each drop, which pallets are left and where. That is the part of multi-drop planning that most plans leave out.

What to do on Monday

  1. For each truck type you use, write down the axle and tyre layout, and look up the rear axle and total limits in the table. Do not use "6-wheel" or "10-wheel" as the key.
  2. Weigh each truck empty at a weighbridge you can reach, axle by axle if the scale allows, and write down the figures. A carrier's registration weight is a starting point only. Fuel, tools and a spare change the real number.
  3. Add the axle limit to the load plan next to the total. Give the loader a rule such as "heavy pallets between the axles".
  4. For multi-drop trips, write the remainder after each drop and check the rear axle against the plan once.
  5. When a truck is not on the table, or a road or bridge has its own sign, ask the carrier for the permitted figure in writing before the booking, not at the weighbridge.

Where the evidence stops: no Thai study of axle overloading on goods trucks was found. The truck weights and distances above are an illustration of the method and not Thai measurements. The limits come from two municipal announcements that were read from PDFs with a scrambled text layer, with the numbers and key words legible. The national highway announcement, the penalty for a breach and the exact reading of each axle configuration should be checked against the announcement that covers your road.